[Lion’s Lecture] A Comprehensive Guide to Inspecting and Troubleshooting Engine Oil, Air, and Coolant Leaks
Release time:
2018-10-24
Mengshi fully synthetic lubricant boasts exceptional shear stability, ensuring reliable performance even under demanding operating conditions. During operation, the most common malfunctions of an engine are the “three leaks”: air leakage, oil leakage, and water leakage.
The engine’s “three leaks” degrade its technical condition, accelerate wear of components, lead to frequent malfunctions, make starting difficult, increase fuel consumption, and reduce power. The “three leaks” phenomenon must be taken seriously and promptly inspected and rectified.
Air leakage at the joint between the engine block and the cylinder head can burn out the head gasket, leading to a reduction in engine power.
Air‑intake system leaks can allow dust to enter the engine cylinders, thereby accelerating wear on components such as cylinder liners, pistons, piston rings, valves, and valve guides.
Engine blow-by noise is a continuous, high-pitched “squeak-squeak” sound that occurs during operation. When the oil filler cap is opened, the noise becomes more pronounced, and a significant amount of gas escapes from the oil filler opening.

Cause of air leakage:
The piston rings do not seal properly against the cylinder walls; the ring gaps are excessively large, or the end joints of the rings align in the same direction; grooves are present on the cylinder walls; the piston rings have insufficient elasticity; or the rings become seized in their grooves.
Methods for detecting and eliminating air leaks:
With the engine speed held steady under conditions where the noise is most pronounced, use a screwdriver to briefly short‑circuit each cylinder’s spark plug in turn, observing whether the noise disappears or diminishes. In any suspect cylinder, add a small amount of engine oil, crank the crankshaft several revolutions, then restart the engine. If the noise lessens or vanishes during initial startup but reappears after a few minutes, this indicates a blow-by leak. If the noise is only slight, the engine may continue to be used; however, if the leak is severe, the piston should be removed for inspection. If the piston rings are seized, remove carbon deposits; if their ends are aligned in the same direction, adjust them according to specifications. If the piston rings have insufficient spring tension or the cylinder liner is excessively worn, replace the rings or overhaul the engine.
Oil and diesel leakage leads to increased fuel consumption, poor cleanliness and appearance of the engine exterior, and makes it difficult to remove the accumulated oil mixed with soot. When lubricating‑system oil seeps into or enters the combustion chamber and burns, the oil level in the crankcase drops; in severe cases, this can result in insufficient lubrication at critical points, preventing the formation of an effective oil film, leaving components unlubricated and causing dry friction that exceeds allowable clearance limits. In the fuel‑supply system, leaks at components such as the fuel transfer pump, injection pump, injectors, and the connecting fittings of the fuel lines can cause intermittent or inadequate fuel delivery, leading to engine knocking, unstable RPMs, poor ignition, or even failure to start. If filters or filter elements are damaged, they must be replaced promptly; otherwise, unfiltered diesel will enter the three precision mating pairs and be injected into the combustion chamber, accelerating wear on these components and internal cylinder parts.

Causes of Oil Leakage
Damage to the front and rear crankshaft oil seals, as well as to the paper gasket between the oil pan and the lower surface of the cylinder block; rupture of the oil line connecting the oil cooler or loosening of its fittings can lead to oil leakage, resulting in a reduction in oil level.
If the crankshaft oil seal, the oil pan, or the paper gasket between the cylinder block and the lower surface are damaged, they should be replaced. To prevent oil leakage caused by rupture of the oil line connecting to the oil cooler, install additional securing points for the oil line during assembly; ensure that other components do not come into contact with the engine block to avoid vibration‑induced damage to the oil line. Replace any ruptured oil lines, and if a pipe fitting has become loose, retighten the nut.

During operation, engine components may wear, develop cracks, or become loosely connected, leading to coolant leaks. Coolant leakage is a common malfunction in diesel engine cooling systems. Such leaks not only complicate refilling but, in severe cases, can cause cylinder head cracking. If the cylinder liner water seal leaks, it can dilute the engine oil in the oil pan, promoting corrosion and accelerating wear; in extreme situations, it may even burn out the bearing shells. Moreover, coolant leaks can cause the engine to overheat, compromising its normal performance.
Causes of leakage 1
Pump water seal failure and poor sealing: cooling water leaks into the gear housing through the water seal, causing the oil level to rise.
Poor sealing of the injector boot O-ring allows coolant to enter the upper portion of the cylinder head and flow through the return oil port into the oil pan, resulting in a rise in the engine oil level.
Cylinder liner seal failure: The cylinder liner seal prevents cooling water from the engine block’s cooling jacket from entering the oil pan. If the seal fails, cooling water will directly leak into the oil pan.
Cylinder head cracks: When cracks develop in the cylinder head base or in the intake and exhaust passages, coolant can leak from the water passages into the piston crown or the intake and exhaust ports, and then enter the cylinder, causing the oil level in the oil pan to rise.
Diagnostic methods and troubleshooting measures 1
To check for leakage from the cylinder liner’s rubber seal, observe under electric lighting whether any water is dripping along the outer edge of the seal. To inspect for cavitation in the cylinder liner, examine the inner bore of the liner to see if water is flowing down.
Inspect the cylinder head for cracks, check the intake and exhaust passages for cracks, and verify that the intercooler is not leaking by looking for water in the intake or exhaust pipes or passages. As for cracks in the cylinder‑head deck, they must be examined by removing the cylinder head.
To check for leaks at the injector boot, high-pressure fuel line fittings, and return line, all can be inspected by removing the cylinder head cover while the engine is running. Alternatively, with the engine at rest, remove the cylinder head cover to examine whether there are any leaks at the injector boots.
Check the oil cooler for leaks by inspecting the low‑temperature cooling water for the presence of water. This is because, during engine operation, if the oil cooler leaks, the oil pressure—being higher than the water pressure—will inevitably cause oil to enter the cooling water.
Inspection for cracks and leaks in cylinder heads, engine blocks, and turbocharger intermediate casings often requires pressure‑testing; visual inspection alone is typically insufficient.
To ensure smooth, trouble-free operation, it’s also essential to have the engine cleaned and maintained on a regular basis.
Further Reading:
What is carbon buildup?
Carbon deposits are primarily formed due to the combustion of fuel inside the engine. Incomplete combustion, or paraffinic gum substances in gasoline that cannot be fully burned. , in Fuel injectors, throttle body, fuel lines, spark plugs Residual deposits in the components, under high-temperature conditions, subsequently transform into carbon deposits.

Over time, this accumulation causes the actuating components to malfunction, resulting in… Difficulty starting, unstable idle, reduced power, and sluggish acceleration. and other phenomena.
The formation of carbon deposits
In everyday driving, many factors can exacerbate carbon buildup, such as:
1. Vehicle Idling for a long time 、 Driving at low speed 、 Ultra-short-distance driving (within 10 minutes or 5 kilometers) and Idling to warm up the engine for an extended period , all of which can result in fuel being injected into the cylinder Incomplete combustion , thereby Accelerates carbon deposit formation 。
2. Low-quality fuel with poor cleanliness contains a large amount of impurities. These impurities are themselves the main constituents of carbon deposits and, moreover, further impair combustion, leading to… Exacerbate carbon buildup Generate.
3. Oil consumption It can also cause carbon buildup.
The MSL Lubricant Engine Deep‑Care Program helps you enjoy worry‑free vehicle maintenance! It effectively cleans internal carbon deposits and sludge, providing comprehensive engine protection; reduces friction to boost power output, lowers fuel consumption, and eliminates unusual engine noises; and delivers exceptional cleaning performance to enhance oil fluidity and improve lubrication efficiency.




Effective lubrication that extends engine life—this is a premium‑grade motor oil proven by racing teams and champion drivers!
If you’re interested in joining our project, please leave a message promptly—our team will get in touch with you right away and arrange for a call from one of Kangzhong’s representatives.
Latest Updates
Due to recent heavy rainfall in several cities, many vehicles have required repairs after being submerged in water. So how should damage to flood‑damaged cars be assessed? What is the specific repair process for water‑submerged vehicles? And how can you prevent improper repairs?
Before we knew it, the Spring Festival holiday is already over, and the Mengshi team has been back at work for two days now. During the holiday, we visited relatives and friends...
[Lion’s Classroom] All About Wheel Alignment
Wheel alignment is based on the vehicle’s four-wheel parameters and involves adjustments to ensure optimal driving performance and a certain level of reliability...
[Lion’s Classroom] Spark Plug Mini-Class
Our cars have thousands of components, each of which is essential. Yet many drivers focus solely on oil changes during maintenance, overlooking small parts like spark plugs. Today, we’ll show you how to determine for yourself whether your spark plugs need replacing.
[Lion’s Classroom] Handy Tips for Tire Maintenance
A journey of a thousand miles begins with a single step. Tires are like the shoes of a car—their condition directly affects driving safety. That’s why tire safety is of paramount importance, and regular maintenance is essential. Now, let’s take a look with the editor at how to properly care for your car’s tires!
Recently, Volvo officially awarded Mingshi Lubricants the VCC RBS0-2AE standard certification for its SN 0W20 product. One technological breakthrough after another has once again demonstrated the exceptional quality of Mingshi Lubricants.